x 

Adafruit Feather HUZZAH ESP8266 WiFi et Headers

z8022_HUZZAH_01
z8022_HUZZAH_02
z8022_HUZZAH_03
z8022_HUZZAH_04
Fournisseurs Adafruit
Référence:  z8022
Disponibilité du produit:   In stock
Feather is the flagship development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.
Prix ​​de vente21,50 CHF

Feather is the flagship development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

This is the Assembled Adafruit Feather HUZZAH ESP8266 with headers - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB and battery charging and ready to go immediately! Its an ESP8266 WiFi module with all the extras you need, ready to rock!

At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can program the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. We wired up a USB-Serial chip that an upload code at a blistering 921600 baud for fast development time. It also has auto-reset so no noodling with pins and reset button pressings.

To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available.

Here's some handy specs!

  • Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
  • Light as a (large?) feather - 9.7 grams
  • ESP8266 @ 80MHz with 3.3V logic/power
  • 4MB of FLASH (32 MBit)
  • Built in WiFi 802.11 b/g/n
  • 3.3V regulator with 500mA peak current output
  • CP2104 USB-Serial converter onboard with 921600 max baudrate for uploading
  • Auto-reset support for getting into bootload mode before firmware upload
  • 9 x GPIO pins - can also be used as I2C and SPI
  • 1 x analog inputs 1.0V max
  • Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
  • Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

Comes fully assembled and tested, with a USB interface that lets you quickly use it with the Arduino IDE or NodeMCU Lua (it comes preprogrammed with the Lua interpreter). This version of the board has also been pre-soldered, so you can plug it right into a solderless breadboard. Lipoly battery and USB cable not included

Tutorial for all sorts of details, including schematics, files, IDE instructions, power management and more


Technical Details

  • 23mm x 51mm x 18mm / 0.9" x 2" x 0.71"
  • Weight: 8g
  • RoHS

Distributeur Suisse de

PololuArduinoAdafruit phpOC ThymioArducam

Expédition

Envoi Suisse
Suisse
Swiss shipping
 
Envoi international
terre001
International shipping

ZigoBot à Lausanne

Horaires de la boutique :

*** Vendredi 19 juillet fermé dès 13h30 ***

du Mardi au Vendredi de 10h à 18h
et le Samedi de 10h à 14h.

Rue de la Grotte 4 (sous la place Saint-François) • 1003 Lausanne

Newsletter